Measuring & Layout · Single tool · Maker · DIY

Digital Calipers: Measure Thickness, Holes and Depth

Our verdict

NEIKO 01407A Electronic Digital Caliper, 0-6 Inch

7.7/10
Worth-owning score

  • Usefulness8/10
  • Value9/10
  • Durability6/10

Price tier Budget ($)

View on Amazon

Our own score from specs, buyer reviews and tests. Not a customer rating. Photo from the Amazon listing.

Quick answer

Digital calipers are a sliding gauge that reads thickness, width, hole size and depth on a screen, down to a few thousandths of an inch. A budget model like the Neiko 01407A did well in Project Farm's smoothness and block tests. Skip them if you only cut lumber to a pencil line, where a tape measure is enough, or if your parts need tolerances tighter than a thousandth, which calls for a micrometer.

What are digital calipers?

Digital calipers are a sliding gauge with a screen that reads the size of a small object to a few thousandths of an inch. You close two jaws on the thing you want to measure, and the number appears on the display. They fill the gap between a tape measure, which is good to about a sixteenth of an inch, and a micrometer, which is a precision gauge for very tight work.

One tool does four jobs. The large jaws measure the outside of something, such as a board, a dowel or a bolt. The small jaws on the back measure the inside of a hole or slot. A thin rod that slides out of the end measures depth. A small step on the jaws measures how far one surface sits below another.

Digital caliperTape measureMicrometer
Typical useThickness, hole size, depthLengths and layoutOne size, very tight tolerance
Reads toAbout a thousandth of an inchAbout a sixteenthA ten-thousandth
Range6 inches on most modelsMany feetAbout 1 inch per tool
Needs a batteryYesNoNot on mechanical ones
The Neiko 01407A screen shown in inch, millimeter and fraction modes
The listing shows the same reading in three modes: inch, millimeter and 1/128 inch fraction. Photo: Amazon listing

Why you'll want a pair

It answers "what size is this?" A bolt, a drill bit, a hole in a bracket or the thickness of a shelf board can all be checked in seconds. That saves a trip back to the store with the wrong fitting. A drill bit set is easier to use when you can confirm a bit's real diameter.

It makes parts fit. Woodworkers use calipers to set a joint to the width of a dowel or tenon. Makers use them to check a 3D-printed part against its design. The machinist in one video we checked uses his for turning parts on a lathe, then watches the screen as he nears the target size.

It reads inch, fraction and millimeter on one screen. The Neiko listing says a quick-change button switches between the three. A video from Adam Savage's Tested also says the inch and millimeter button is handy.

A budget pair is reasonable. A machinist who compared a budget Neiko with a Mitutoyo, a premium Japanese brand, said there was no meaningful difference in accuracy between the two on gauge blocks, so for most home projects either will do.

What can calipers measure around the house?

JobWhich jawsWhat you learn
Bolt or screw diameterOutsideThe thread size before you buy a nut
Drill bit or dowelOutsideThe true diameter, which can differ from the label
Plywood or board thicknessOutsideReal thickness, since sheet goods run under their nominal size
Hole or pipe openingInsideWhether a bolt or fitting will fit
Depth of a hole or slotDepth rodHow far a screw or a pin can go in
Shelf pin spacingOutside and insideA repeatable size for a jig

Who it's for

  • Makers and woodworkers checking board thickness, a dowel, a shim or a joint to a thousandth
  • 3D printer owners measuring a printed part against the design
  • DIYers checking a bolt, a drill bit, pipe or a hole before buying a fitting
  • Hobbyists working on models, bikes, guitars or electronics with small parts

Who should skip it

  • Anyone who only cuts to a pencil mark. A tape measure is faster for lumber and room layouts.
  • Anyone who needs tolerances tighter than a thousandth. One machinist says to use a micrometer for that.
  • Anyone who wants a gauge that never needs a battery or a zero. A dial caliper has no battery, and Adam Savage says he now prefers one for that reason.

How to use them

Wipe, close, zero, measure, read. Five steps make the number trustworthy.

  1. Wipe the jaws clean. A speck of dust or sawdust is enough to shift the reading. Project Farm wipes the jaws before every test.
  2. Close the jaws and press zero. The screen should show 0.000. This sets the starting point on a normal budget caliper; the Neiko is relative, as the machinist's video explains, so the zero is wherever you last pressed the button.
  3. Pick the unit. Press the inch / fraction / millimeter button until the screen shows what you want. The Neiko listing says it has three modes.
  4. Close the jaws gently on the part. Use the thumb wheel and stop as soon as the jaws touch. Squeezing bends the jaws slightly, which is why Project Farm closed them with a light, steady weight in his accuracy test.
  5. Hold the part square. Tilting a caliper across a round bolt or a board edge reads too large. Keep the beam parallel to the part.
  6. Lock the jaws if you need to move the tool. The locking screw holds the reading while you pull the calipers away to read the screen in a better light.
  7. Read the display, not the scale. The printed scale on the beam is a backup. The screen is the one to trust.
  8. Take the reading twice. A repeat tells you whether your grip, or a speck of dirt, moved the number.
  9. Use the depth rod for holes. Rest the end of the beam on the surface and slide the rod down until it touches the bottom. Hold the beam flat to the surface.
  10. Take the battery out for long storage. Adam Savage says his digital calipers' batteries were always dead after months on a shelf. Reader comments under Hackaday's write-up say the same, and taking the cell out for storage is a common habit.

What reviewers and buyers say about the Neiko 01407A

  • Praised: Bob Vila's testers like how easy it is to operate and name it the pick for easy operation. They say the thumb wheel makes it quick to switch between outside, inside and depth measurements, and that the contrasting rule and display are easy to read. Project Farm found it smooth and consistent across the full length of the slide.
  • Common complaints: Bob Vila's testers say the decimal digits get smaller than the main number, and note no warranty and no IP54 water and dust rating. A reviewer reported that the first battery in his unit was dead and the screen showed gibberish until he fitted the spare. The listing itself calls it splash and dust resistant.
  • Independent tests: In Project Farm's test it read the one-inch and two-inch blocks exactly and was 0.0005 inch over at three inches. On the depth test it read 1.001, 2.0005 and 3.001 inches. Its tips did not reach the bottom of his narrow test groove (0.3185 inch against a true 0.303), though that was better than the cheapest wide-tipped models.
  • Durability: The machinist who compared them says his own cheap pair failed after about three years, drifting off to wrong readings, and calls it a possible fluke. He also says a Mitutoyo is the safer bet for use all day, every day.

Three common traps

TrapWhat happensFix
Dirt on the jaws or scaleA false reading, or a number that driftsWipe the jaws and close and zero again
Squeezing the jawsThe reading shifts as the jaws flexClose lightly with the thumb wheel
Zero set with the jaws openEvery reading is off by that amountClose the jaws fully before pressing zero

What to look for when buying

  • Range. Six inches (150 mm) covers most home jobs. Pick 8 inches or more only if you will measure large parts.
  • Smooth slide. Project Farm ranked the models by how evenly the jaw glides. The Mitutoyo felt smoothest, the Neiko was second and a Starrett was third.
  • Sharp, narrow tips. They reach into grooves, and wide ones read a narrow groove too large.
  • Absolute zero. Only a few models in Project Farm's lineup (the Quinn, Fowler and Mitutoyo) remember their zero when switched off. It saves a step, and it costs more.
  • Auto shut-off and battery type. Project Farm notes a CR2032 cell has about twice the capacity of the more common LR44, and says some models switch themselves off when idle.
  • Water and dust rating. The IP54 rating on some models, such as the iGaging in Bob Vila's test, helps in a dusty shop. The Neiko has none.
  • A case and a warranty. The listing includes a hard case; Bob Vila's testers say it has no warranty.
  • Know the limits. If a project needs tolerances under a thousandth of an inch, use a micrometer. For marking and layout, a pencil or marking knife and a speed square are better tools, and a laser distance meter handles room lengths.
  • Buy from a trusted seller. The machinist who compared them says to check that the seller is Amazon, because a third-party seller of a premium model can ship a counterfeit.
The Neiko 01407A digital caliper resting in its foam-lined case with a small screwdriver
A case keeps the jaws and scale clean. The listing includes one. Photo: Amazon listing

Key specs to look for

SpecWhat to look for
Range0 to 6 inches (150 mm) on the Neiko, per the listing. Six inches covers boards, pipe, bolts and most small parts; larger jobs need an 8 or 12 inch model.
ResolutionThe smallest step on the screen: 0.0005 inch or 0.01 mm on the Neiko. A finer step looks more exact but is not the same thing as accuracy.
Accuracy0.001 inch (0.02 mm) per the Neiko listing. A video by a machinist says anything within a thousandth is a successful caliper measurement.
UnitsA button that flips between inch, millimeter and fraction. The Neiko listing adds a 1/128 inch fraction mode.
Jaw tipsNarrow, sharp outside tips fit into small grooves. Project Farm found wide tips read a narrow groove too large.
Zero typeMost budget models are relative: you close the jaws and press zero. An absolute (origin) caliper remembers its position when switched off.
Slide feelThe jaw should glide with an even drag. Project Farm measured the force needed to slide each jaw and found large differences.
Battery and caseA coin or button cell, plus a case. A reviewer found his Neiko came with a spare battery and that the first one was dead.

Where to get it

Our featured pick is below, chosen from the listing, Bob Vila's tests and Project Farm's results. If you want a step up in feel and a zero that stays set, reviewers point to the Mitutoyo Digimatic line, though it costs far more than a basic caliper. In Project Farm's test, a lower-cost WORKPRO model scored nearly as well as the premium brands, so it is also worth a look in our Tool finder.

NEIKO 01407A Electronic Digital Caliper, 0-6 Inch

Budget ($)Worth-owning score 7.7/10

  • A 0 to 6 inch (150 mm) range, a 0.0005 inch / 0.01 mm display step and a stated accuracy of 0.001 inch / 0.02 mm, according to the listing
  • A quick-change button that switches between inch, fraction and millimeter, plus a thumb roller, a locking screw and a hard case, per the listing
  • In Project Farm's test of more than fifteen calipers it was the second smoothest slide and scored within 0.0005 inch cumulative error on a precision block; he named it his budget choice after one other model
View on Amazon
How we scored it

Usefulness 8/10 · Value 9/10 · Durability 6/10. This is our own opinion, based on specs, buyer reviews and independent tests. It is not an Amazon or customer rating.

Watch and read more

Video reviews

Frequently asked questions

What do digital calipers measure?

Four things. The large jaws measure the outside of an object, such as a board or a bolt. The small jaws on the back measure the inside of a hole or slot. A thin rod at the end measures the depth of a hole. The step edge measures how far one surface sits below another.

Do I need to zero the calipers every time?

On a normal budget model, yes: wipe the jaws, close them and press zero before a measurement. A machinist's video explains that these are relative calipers, so the zero is wherever you last pressed the button. An absolute model, such as the Mitutoyo he compared, remembers its position.

How accurate are cheap digital calipers?

Closer than most people expect. In Project Farm's block test, several budget calipers read a precision block to within a few ten-thousandths of an inch, and Hackaday's summary of the test says price did not predict accuracy. A machinist who compared a budget pair with a Mitutoyo found no meaningful accuracy difference.

Why does my reading change when I press harder?

Squeezing the jaws bends them a tiny amount. Project Farm used a light string-and-weight trick to close the jaws with a steady force. By hand, close the jaws until they just touch the part and use the thumb wheel lightly.

Can I measure a narrow groove with calipers?

Only if the outside tips are thin enough. Project Farm cut a groove into a bolt: the wide-tipped models read it far too large, and none reached the true bottom, so use a groove or O-ring gauge for exact work.

Why does the screen show nonsense or stay on 0.000?

Usually the battery. A reviewer saw gibberish on a new Neiko and fixed it by swapping in the spare battery. Clean the jaws and the scale too, since dirt on either one can upset a reading.

Are digital calipers better than dial or vernier calipers?

They are quicker to read and switch between inch and millimeter at the push of a button. Dial and vernier calipers need no battery. Adam Savage says his digital calipers' batteries were often dead after sitting for months, so he picked up dial calipers instead.

Sources